Skip to content
Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6Black Friday & Cyber Week — 10% Off Everything + Extra 5% Off 10+ Items · Extra 10% Off 50+ Items Free Worldwide Shipping on Orders Over $500 Ends December 6
Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+Cyber Week — 10% Off All + Extra 5% on 10+ · 10% on 50+ · Free Shipping $500+
Active vs Passive GNSS Antenna: How to Choose the Right One

Active vs Passive GNSS Antenna: How to Choose the Right One

Use a passive GNSS antenna only when it sits very close to the receiver, typically on the same board or within a few centimeters of thin cable. If the antenna is mounted on a roof, a vehicle exterior or an enclosure lid more than a short distance away, you need an active antenna with a built-in low-noise amplifier (LNA) to overcome cable loss.

Why GNSS antennas are different from other RF antennas

Satellite navigation signals arrive at the Earth's surface far below the thermal noise floor, roughly -125 to -130 dBm for GPS L1. Every decibel of loss or added noise before the first amplifier reduces the carrier-to-noise ratio (C/N0), which means slower fixes, fewer usable satellites and more dropouts. That is why the antenna and its first amplifier matter more in GNSS than in most cellular or Wi-Fi designs.

Active vs passive GNSS antennas

Passive antennas

A passive antenna is only the radiating element, usually a ceramic patch, a chip antenna or a helix, with no amplifier. It is cheaper, draws no current and works well when the receiver sits directly beneath the antenna or on a short, low-loss trace. A module's internal LNA cannot recover signal already lost in a long cable. Browse typical options in the passive GPS antenna category.

Active antennas

An active antenna places an LNA, and usually a band-pass or SAW filter, right behind the radiating element. Because the amplifier sits before the cable, the cable loss that follows has much less effect on the overall noise figure of the system. Active antennas are powered through the coaxial cable by a DC bias voltage supplied from the receiver. They are standard for vehicle tracking, timing, rooftop installations and any enclosure where the antenna sits away from the electronics. See the active GPS antenna range for examples.

LNA gain, noise figure and cable loss

Two LNA parameters dominate performance:

  • Noise figure (NF): The noise the first amplifier adds. Because of how cascaded noise works (the Friis formula), the first stage sets most of the system noise. Good GNSS LNAs are commonly around 1 to 2 dB; a poor LNA can perform worse than a well-placed passive antenna.
  • Gain: Typical active GNSS antennas offer somewhere between roughly 15 and 40 dB of gain, with mid-20s to around 30 dB being very common. It must cover cable loss without overloading the receiver.

A practical budgeting rule

Check your receiver datasheet for the recommended range of net gain at its RF input (antenna gain minus cable and connector losses). As a rule of thumb, aim for the antenna LNA gain to exceed total cable loss by a comfortable margin while staying inside the receiver's recommended window. Too little hurts sensitivity; too much can saturate the receiver, especially near cellular transmitters.

Cable loss at GNSS frequencies (around 1.2 to 1.6 GHz) varies widely with cable type. Thin RG-174 or micro-coax loses roughly a decibel or more per meter, RG-58 class about half that, and LMR-400 class cable a fraction of a decibel. Use the manufacturer's attenuation figure and add about 0.1 to 0.5 dB per connector.

When an active antenna is required

  • The cable between antenna and receiver is longer than a few tens of centimeters.
  • The antenna is outside a metal enclosure or vehicle body while the receiver is inside.
  • You are using a GNSS splitter to feed more than one receiver.
  • The receiver has no internal LNA, or its datasheet specifies an external active antenna.

Multi-band and multi-constellation support

Modern receivers can track several constellations and frequency bands at once, but only if the antenna covers them. An antenna labeled "GPS" may be tuned narrowly around 1575.42 MHz and perform poorly on other signals.

Constellations

GPS (USA), GLONASS (Russia), Galileo (EU) and BeiDou (China) all broadcast in the upper L-band. GPS L1, Galileo E1 and BeiDou B1C share 1575.42 MHz, while BeiDou B1I sits slightly lower near 1561 MHz and GLONASS G1 occupies roughly 1598 to 1606 MHz. A full multi-constellation antenna must cover about 1559 to 1606 MHz.

Multi-band: L1/L5 and L1/L2

Dual-frequency positioning lets the receiver estimate and remove ionospheric delay and reject multipath more effectively. Two common pairings exist:

  • L1/L5 (L5, E5a and B2a around 1176.45 MHz): common in newer mass-market and automotive receivers.
  • L1/L2 (GPS L2 at 1227.60 MHz, GLONASS G2 near 1246 MHz): long established in survey and RTK receivers.

Match antenna bands exactly to the receiver; a dual-band receiver on a single-band antenna behaves like a single-band receiver. For RTK and precise point positioning, also look at phase center stability and phase center variation, which matter more than raw gain. Compatible receivers are listed under GPS/GNSS modules.

Polarization and axial ratio

GNSS satellites transmit right-hand circularly polarized (RHCP) signals. A matching RHCP antenna receives the direct signal well and tends to reject reflections, because a single reflection largely reverses the polarization to left-hand. Linear antennas, such as some chip antennas, lose about 3 dB against a circular signal and are more sensitive to multipath.

Axial ratio describes how close the antenna is to ideal circular polarization. Lower is better: values around 3 dB or less at zenith are typical of decent antennas, and high-precision designs keep axial ratio low down toward the horizon. Also check gain at low elevation angles, which affects tracking of satellites near the horizon.

Ground plane, mounting and sky view

Patch antennas are tuned to work with a specific ground plane. A ceramic patch designed for a large metal ground plane can detune and lose gain when mounted on a small PCB or a plastic surface. Check the datasheet for the reference ground plane size, and if your mounting surface differs, choose an antenna with an integrated ground plane or a housing designed to be ground-independent.

  • Mount the antenna with the clearest possible view of the sky, ideally horizontal and facing up.
  • Keep it away from cellular, Wi-Fi and other transmitting antennas; separation and filtering reduce desensitization.
  • Avoid metallized windows, heated windshields and solar films, which can attenuate signals heavily.
  • Outdoors, use a weather-rated housing and a grounded surge arrester on the coax.

For vehicles and gateways that also carry LTE, combination antennas in the general antenna collection simplify installation.

Connectors

  • SMA: The common threaded connector for external antennas on modules, routers and evaluation boards. Robust and easy to source.
  • U.FL / IPEX: Tiny board-level connectors for use inside enclosures, rated for few mating cycles.
  • FAKRA: Keyed, color-coded automotive connectors that prevent mixing up GNSS and cellular cables.

Every adapter adds loss and a failure point, so order the correct connector and cable length instead of chaining adapters.

Supplying antenna bias voltage

Active antennas receive DC power over the center conductor of the coax. The receiver or module either provides this bias directly on its RF input, or the designer adds a bias-tee circuit (an inductor feeding DC and a capacitor blocking it from the receiver input). Verify:

  • The antenna's supply voltage range matches what the receiver provides; 3.3 V and 5 V are the most common values, and many antennas accept a range.
  • The receiver can supply the current draw, usually a few to a few tens of milliamps.
  • Current limiting protects against shorted cables.
  • When using splitters, only one port should pass DC to the antenna; the others need DC blocks.

Common mistakes

  • Using a passive antenna on a long cable and blaming the receiver for poor fixes.
  • Choosing an L1-only antenna for a dual-band receiver.
  • Forgetting to enable or provide bias voltage, leaving the active antenna unpowered.
  • Excessive gain that overloads the receiver, especially near cellular modems.
  • Mounting a patch antenna on a surface very different from its designed ground plane.

Selection checklist

Requirement What to check Typical guidance
Cable length Distance from antenna to receiver Very short: passive can work. Longer: active with adequate LNA gain
LNA gain Gain minus total cable and connector loss Stay within the receiver's recommended net input gain
Noise figure LNA datasheet Lower is better; around 1 to 2 dB is common for quality designs
Bands L1 only, L1/L5 or L1/L2 Match exactly to the receiver's supported signals
Constellations GPS, GLONASS, Galileo, BeiDou coverage Bandwidth covering about 1559 to 1606 MHz for full upper L-band
Polarization RHCP and axial ratio RHCP with low axial ratio, around 3 dB or less at zenith
Ground plane Reference ground plane in datasheet Match it, or choose a ground-independent housing
Bias supply Voltage and current Commonly 3.3 V or 5 V; confirm current and protection
Connector SMA, U.FL/IPEX, FAKRA, TNC, N Correct connector and cable length, minimal adapters

Key takeaways

  • Passive antennas suit designs where the antenna is right next to the receiver; anything farther needs an active antenna.
  • The LNA noise figure sets most of the system noise; gain only needs to cover cable loss within the receiver's limits.
  • Antenna bands and constellation coverage must match the receiver, especially for L1/L5 or L1/L2 designs.
  • RHCP polarization, low axial ratio and a correct ground plane improve accuracy and multipath rejection.
  • Sky view, transmitter separation and a clean cable path often matter as much as the antenna itself.

Frequently asked questions

Can I use an active antenna with a receiver that does not supply bias voltage?

Not directly. Without DC on the coax, the LNA is unpowered and the antenna performs worse than a passive one. Add an external bias-tee with a suitable supply, or choose a receiver that provides antenna power.

Is more LNA gain always better?

No. Gain beyond what is needed to overcome cable loss can push the receiver into compression and make it more vulnerable to interference from nearby transmitters. Stay inside the receiver's recommended input gain range.

Do I need a multi-band antenna for asset tracking?

For general tracking, a good L1 multi-constellation antenna is often sufficient. Multi-band antennas pay off when you need lane-level or centimeter-level accuracy, better performance in urban canyons, or RTK correction services.

Browse the GNSS antenna collection, and if you are planning a deployment, LynxPi's team can help you match antennas, cables and modules to your application. For larger quantities, request a volume quote.

Previous article Industrial 4G/5G Router Buying Guide for Remote Sites
Next article 2G/3G Sunset: A Practical IoT Migration Guide to LTE

Need these components in volume?

Our B2B team sends volume pricing and lead time within one business day — and helps you choose the right part.

← All articles